Menu Close

Thies First Class Advanced X Anemometer: 4.3352.00.400- heated

Make:  Thies Clima    Model: 4.3352.00.400 – heated
✅ The wind transmitter is intended for use in the wind energy, meteorology and environmental measuring technology.
✅ Measurand : Horizontal component of the wind velocity,Absolute and relative air pressure,Frequency and acceleration in the X-, Y- and Z-axis,Housing interior temperature.
✅ Senso Type : Cup Anemometer
✅ Signal Output : RS485 / ASCII / MODBUS and Frequency output.
✅ Supplied With : Connection plug, Instructions for use, Factory test/ Calibration Certificates.
Compare

The wind transmitter is intended for use in the wind energy, meteorology and environmental measuring technology. Primarily developed for position evaluation and measurement of power curves of wind turbines, the anemometer gathers the following measured variables: Horizontal component of the wind velocity, Absolute and relative air pressure, Inclination angle between the Z-axis and the vertical, Inclination angle between the X-axis and the horizontal, Inclination angle between the Y-axis and the horizontal, Frequency and acceleration in the X-, Y- and Z-axis, Housing interior temperature.

Further characteristics include a defined and optimized dynamic behavior even at highly intense turbulences, minimal over speeding, a low starting value and an optimized oblique inflow behavior.
An integrated compensation of the effect of the air density on the rotation velocity of the cup star distinguishes this sensor especially in its characteristics. There is a digital interface to the device in form of an RS485 interface in half-duplex mode. Together with the ID-based communication, the interface enables the operation of the wind transmitter in a bus. Two data protocols are available:

  • ASCII (THIES format).
  • Binary (MODBUS-RTU).

For operation in winter, the device can be equipped optionally with an electronically controlled heater which provides a hardly measurable friction moment of the ball bearings in low temperatures and prevents any ice build-up on shaft and on the gap.

Make

Thies Clima

Model

4.3352.00.400 – heated

Weight (Mass)

approx. 0.5kg

Dimension

290 × 240 mm

Outputs

Type : open-drain or push-pull
Form : rectangle
Frequency : 1082Hz @ 50m/s without using calibration data
Amplitude : corresponds to supply voltage, max. 15V
Load : Ra > 1 kΩ (Push-pull output with 200Ω in series), Approx. <200nF (corresponds to a cable length ~ 1km)

Power Supply

Electric supply for electronic :
Voltage : 3.7 … 42V DC (galvanically separated from the housing)
Current : 40mA typ. 100mA max. (with heating pressure sensor on), approx. 3.3mA in power saving mode SM1, HT0
Electric supply for Housing heater :
Voltage : 24V AC/DC, 45 … 65Hz
Open circuit voltage : max. 30V AC, max. 42V DC
Wattage : 25W
Proportional control, control temperature: 5°C, Heater can be enabled disabled via interface, galvanically separated to the housing and the measured value logging

Operating Environment

Admissible environmental conditions : -40 … +80°C/ 0 … 100% relative humidity, including condensation

Protection Level

IP 55 (DIN 40050)

Standerd / Regulation

IEC 61400-12-1

Mast Diameter

Mounting on mast :
Outer diameter : ≤ 34mm
Inner diameter : ≥ 22mm
Note: mounting on mast is possible with separate adapter (option).

Wind Speed

Measurement range: 0.3 … 75m/s
Resolution: 0.05m wind travel
Measurement uncertainty ±1% from the measured value or < ±0,2m/s @ 0,3 … 50m/s

Reviews

There are no reviews yet.

Be the first to review “Thies First Class Advanced X Anemometer: 4.3352.00.400- heated”

Your email address will not be published.